NAV
【Category】：Rotary evaporator
【Range】：Laboratories, pharmaceutical companies, schools, for evaporation, distillation, separation of chemicals
【Description】：Re-2010 rotary evaporator (1L), the evaporation bottle rotates at a constant speed, and the water bath is heated at a constant temperature. Under this condition: the material forms a large area of uni
| 项目描述 | 产品详情 |
| 产品介绍 | Re-2010 rotary evaporator (1L), the evaporation bottle rotates at a constant speed, and the water bath is heated at a constant temperature. Under this condition: the material forms a large area of uniform film on the inner wall of the evaporation bottle and evaporates quickly. Under vacuum conditions, the evaporation efficiency can be improved (it is necessary to connect the vacuum device). When the solvent steam passes through the glass condensation coil, it is cooled into liquid (it is necessary to connect the cooling device) and recycled in the collection bottle. |
| 基本配置 | 1、主体支架采用铝合金，结构合理，用料讲究。 |
| 2、密封系统采用特氟龙+进口氟橡胶组合双向密封，能保持高真空度。 | |
| 3、玻璃部件全部采用高硼硅玻璃（GG-17），耐高温，防腐蚀。 | |
| 4、可连续进料方便客户使用，阀门式加料管套接四氟乙烯管。 | |
| 5、直立式双层蛇形盘管冷凝器，确保高回收率，附加料管。 | |
| 6、温度数字显示、智能恒温控制，PT100型传感器快速、准确传递温度。 | |
| 7、熔断器安全保护，并具有防干烧自动断电功能。 | |
| 8、电子无极调速（0-200rpm），旋转设定，操作方便。 | |
| 9、锅胆采用不锈钢+特氟龙复合锅,全封闭加热。 | |
| 10、微电机驱动，主机自动升降。 | |
| 注意事项 | 1、玻璃零件接装应轻拿轻放，装前应洗干净，擦干或烘干。 |
| 2、各磨口、密封面密封圈及接头安装前都需要涂一层真空脂。 | |
| 3、加热槽通电前必须加水，不允许无水干烧。 | |
| 4、必须使保险拧入保险孔内，以免损坏烧瓶。 | |
| 5、如真空抽不上来需检查： ⑴ 各接头，接口是否密封； ⑵ 密封圈，密封面是否有效； ⑶ 主轴与密封圈之间真空脂是否涂好； ⑷ 真空泵及其皮管是否漏气； ⑸ 玻璃件是否有裂缝，碎裂，损坏的现象； | |
| 6、关于真空度 真空度是旋转蒸发器最重要的工艺参数，而用户经常会碰到真空度打不上问题。这常常和使用的溶媒性质有关，生化制药等行业常常用水、乙醇、乙酸、石油醚、氯仿、等作溶媒，而一般真空泵不能耐强有机溶媒，可选用耐强腐蚀特种真空泵。 检验仪器是否漏气的方法：夹断外接真空皮管，观察仪器上真空表，能否保持五分钟不漏气。如有漏气，则应检查各密封接头和旋转轴上密封圈是否有效。反之，仪器正常就要检查真空泵和真空管道。 | |
| 7、关于电机温升 本仪器电动机采用三相，220V专用电机，E级绝缘，绕组采用聚脂高强度漆包线，在海拔不超过1000米，环境温度不超过40℃时连续使用电机表面温升（电机表面温度与环境温度之差）不超过45℃属正常，若温升超过45℃要检查有关传动润滑系统. | |
| 图片详解 |
|
基 | 规格型号 | RE-2010(1L) |
| 电压/频率 | 220V/50HZ ( 可定制110V/60HZ ） | |
| 旋转电机功率 | 30W | |
| 加热功率 | 1300W | |
| 真空度 | 0.098Mpa | |
| 蒸发能力 | 20ml/min | |
| 旋转瓶容量 | 茄形1000mlφ131mm/24#标口 | |
| 收集瓶容量 | 球形500mlφ105mm/24#球磨口 | |
| 旋转速度 | 0-120rpm/min | |
| 控温范围 | 0-99℃ ( 可选0-400℃ ) | |
| 控温精度 | ±1℃ | |
| 玻璃温度范围 | -80-250℃ | |
| 浴锅升降行程 | 150（mm） | |
| 冷凝器尺寸 | Φ85×450mm 上29#标口配玻璃抽气头 下29#标塞 | |
| 冷凝面积 | 0.17㎡ | |
| 四通瓶口径 | 上29#标口 下24#标塞 左19#标口 右24#标塞 | |
| 加料阀 | 19#标塞阀 进料咀（宝塔接头）外径10mm | |
| 真空抽气咀 | 29#标塞 真空咀（宝塔接头）外径10mm | |
| 冷凝盘管进出循环咀 | 宝塔接头外径12mm | |
| 锅胆尺寸容量 | Φ220×120Hmm 约4.5L （ 可加配有机透明罩） | |
| 外形尺寸 | 570×400×(630×880)(mm)宽深高 | |
| 机器净重 | 11.5Kg | |
| 包装尺寸 | 600×460×470mm 纸箱0.13m³ | |
| 包装重量 | 12.5Kg |
Zlgj-12/ multi manifold gland type vacuum freeze dryer can sublimate substances directly from solid state to gaseous state at the "three-phase point", so that they are evacuated by vacuum, and the wat
Zlgj-10 ordinary vacuum freeze dryer, 7-inch true color industrial embedded touch screen +sh-hpsc-i modular controller, high control accuracy, stable and reliable performance. Suitable for loading bul
Znhw-dl intelligent digital display constant temperature (multi connection) electric heating sleeve can be heated at the same time, and can also be operated independently. It has its own flask clamp f
Pthw-dl temperature regulating (multi connected) electric heating jacket temperature control adopts computer chip as the main control unit, adopts multiple digital filter circuits, fuzzy PID control a
Znhw intelligent digital display thermostatic electric heating jacket uses alkali free glass fiber as insulating material, Cr20Ni80 alloy wire spring is installed in it, aluminum silicate cotton is us
Pthw electric heating jacket is an electric heating jacket that realizes constant temperature heating through electronic pressure regulation. It uses alkali free glass fiber as insulating material, Cr
Offer
4000-111-217
Technical consultation
